green glue alternative

Green Glue is a viscoelastic compound used to damp sound transfer. However, it is pricey and only works between rigid materials in interior locations. If you need Green Glue alternatives, there are other products out there that work.

Green Glue Alternative? Any material that will isolate, control, or damp sound frequencies in a constrained layer is an alternative to Green Glue. Materials that don’t need to be sandwiched between layers but block frequencies work too. Much depends on the frequency range to be controlled, their amplitude, and where control is needed.

Reducing noise transfer is big business today. Many products claim to damp or control sound frequencies. In this article, we’ll take a look at Green Glue, 7 alternatives that work, and then some that don’t.

What is Green Glue?

Green Glue Noiseproofing Compound dampens vibration. It is a viscoelastic material, which means it stays pliable and elastic and doesn’t dry out or harden, qualities that make it a good isolator for soundproofing. Sound waves are vibrations that travel through the air. When they hit a solid, they speed up as they travel through it. 

The Compound acts as an anti-vibrational layer, converting sound wave energy into heat. It is used for constrained layer damping, which means it needs to be compressed between two or more layers of solid building material to be an effective sound control material. Green Glue aids in decreasing noise transfer between rooms.

Green Glue Noiseproofing Sealant is a similar material to the Compound. It is recommended for filling gaps around walls or electrical openings up to 1/4-inch but will work on spaces less than 5/8-inch.

The Sealant provides an acoustic seal and prevents noise leakage. It works in conjunction with the Compound to create a sound barrier.

Advantages & Features

Green Glue Compound can be applied in new builds and renovations between layers of drywall, OSB, or plywood. It can be used in floor, wall, and ceiling construction to mitigate sound movement, improving the STC rating. It’s easy to apply in any pattern and cleans up with soap and water before it cures.

The Sealant is used to acoustically seal gaps around electrical and fixture boxes, around doors, and in joints where walls meet the ceiling, floor, and each other. The sealant is quick and easy to apply and can be taped, mudded, or painted within 48 hours of application after it cures. It stays pliable and doesn’t dry out or crack, and improves the STC too.

The products are low odor and V.O.C. substances and have been independently tested for fire and environmental safety. They both can also assist in LEED certification. The Compound and Sealant have also been independently tested for damping effectiveness, and are trusted by architects, builders, and DIYers.

Applications

Green Glue Compound comes in 29-ounce tubes or 5-gallon pails. It can be applied with a quart-size common caulking applicator or a bulk caulking gun or trowel for the pails. It uses two tubes per 4’x8’ sheet, and is applied in any pattern; it doesn’t have to be spread evenly. Spread on drywall, plywood, or OSB and sandwich it against another solid panel and screw the two layers together.

The Sealant comes in a 28-ounce tube and is applied with a standard caulking gun too. Cut a 1/4″ hole in the tip, and use it to fill joints and gaps around utility boxes, and between walls and ceiling or floor. The gaps should be less than 5/8” unless a backer piece is used.

Green Glue Performance

Green Glue Noiseproofing Compound reaches peak performance after 30 days. It takes that long for the water in the compound to evaporate. For optimum damping performance, the room should be between 65°F and 85°F since it is temperature-sensitive. The Sealant and Compound effective damp noise transfer between rooms

Limitations

Green Glue Sealant and Compound are not for exterior use as they are affected by temperature fluctuations. Despite the name, the mixture isn’t adhesive glue and shouldn’t be used as such.

The Compound is for use between rigid building panels as a constrained layer, so it isn’t effective between soft or flexible materials. The Sealant provides an acoustic barrier in gaps and joints but isn’t a sealant for use to seal around pipes, plumbing, or in damp or wet areas.

Green Glue STC

Green Glue will improve the STC rating of an interior wall by up to 10 points, depending on the construction assembly of the wall. A 16” OC 2×4 wall with 1/2” drywall on both sides has an STC of 32.

The same wall framing with the cavities filled with R-13 fiberglass batts and enclosed on both sides with two layers of 5/8” gypsum with Green Glue between, will deliver an STC of 55. Add a resilient channel to one side, and the STC jumps to 62.

Studs at 24” centers have slightly higher STC values, as do steel studs.

7 Green Glue Alternatives That Work

Green Glue Compound and Sealant are not the only products that provide anti-vibrational noise proofing. Here are some other products that effectively stop sound transfer through constrained layer damping, or that fill gaps, and joints.

1. QuietGlue Pro

QuietGlue Pro is a viscoelastic compound used to damp sound vibrations. It is available in 28-ounce tubes or 1 and 5-gallon pails. The water-based material is low odor and VOC and is solvent-free.

The Pro mixture can be used in walls, floors, and ceilings. It will dissipate up to 90% of the noise transfer from home theater or entertainment systems.

The product is easy to apply to drywall, OSB, or plywood. Run a 1/4″ to 3/8” thick bead in any pattern on a rigid sheet and fasten it to pieces already secured. When sandwiched between rigid building panels, it is an effective anti-vibration barrier, improving the STC by up to 10 points.

No products found.It is recommended that 2 tubes be used for each 4’x8’ sheet. The compound should cure in 24 to 48 hours.

Quiet Glue can be used in residential and commercial new construction or renovations to control sound frequency vibration transfer. It is a quick way to soundproof an existing wall; just apply to a new sheet and fasten to an existing one.

The compound is for interior use only and should be stored between 40°F and 100°F.

 

2. Auralex Acoustics STOPGAP Acoustical Sealant

Auralex Acoustics STOPGAP is a viscoelastic sealant used to prevent noise transfer around wall and utility box perimeters. The water-based material stays elastic 5X longer than similar products when cured. It is easy to use, has no run-off residue, but has a slight odor until cured.

It has a tough white surface film when it dries, and is paintable. The sealant is available in 28-ounce tubes and requires a 1-quart caulking gun for application.

The Sealant helps achieve an STC of 53 when applied around a wall’s perimeter following ASTM C-919 directions. The manufacturer recommends two 3/8” beads be applied around the wall perimeter for the best results.

One tube will provide between 32 and 40-feet of 3/8” bead. The product is flame-retardant and meets ASTM E-84 requirements. STOPGAP can be used for wall, floor, and ceiling applications in commercial or residential renovations and new builds.

 

3. Mass Loaded Vinyl

Mass Loaded Vinyl (MLV) is a dense, heavy yet flexible black, gray, or transparent vinyl soundproofing material. It has calcium carbonate or barium sulfate mixed into it to increase the mass. The vinyl is available in 1/2lb (1/16”), 1lb (1/8”), and 2lb (1/4”) per square foot weights, in lengths to 100-feet, and between 24” and 54” wide.

It has an independent STC rating of 20, 26, and 33 depending on weight and thickness. MLV is used to block mid to high range frequencies. It has little or no odor and is used in residential, medical, and commercial facilities, both renovations and new builds. It is also paint friendly.

The vinyl’s STC properties combine with wall, floor, and ceiling construction methods for added soundproofing. It can be hung between studs and drywall or sandwiched between two gypsum layers to improve the soundproofing of walls and ceilings.

Additionally, it may be used between floor layers for the same effect. MLV improves sound isolation when wrapped around ducts and plumbing, and can even be used to curtain windows. The heavy-weight vinyl is effective at stopping sound frequency vibrations from penetrating.

Soundsulate Mass Loaded Vinyl with Fiberglass Decoupler

Soundsulate MLV combines 1-pound MLV with a layer of 1” or 2” fiberglass insulation and reflective foil. It provides flexible acoustic and thermal insulation to absorb and block sound.

It works well around HVAC, ductwork, and plumbing pipes to stop noise transfer, plus works well in drop-ceilings or between joists.

 

4. Tremco Acoustical Curtainwall Sealant

No products found. is a single-component, non-skinning, dark gray synthetic rubber material that doesn’t harden. Due to the flexible rubber-like characteristics, it is good for sound damping.

The sealant is available in 10 and 28.7-ounce tubes and 5-gallon pails. The 28.7-ounce container requires a quart-sized caulking gun for application. One cartridge will do about 27 linear feet in a 1/4″ bead.

The product provides an acoustic seal for wall perimeters and lap joints. When used to seal all wall, ceiling, or floor gaps, the rubber improves the STC rating of the wall assembly.

It can take if from an STC of 19 to 54, depending on bead placement and the number of beads applied. LEED certification can be achieved using Tremco Sealant.

The sticky paste doesn’t dry or cure, so it should be covered, so it doesn’t attract debris or smear. It can also be used to seal vapor barriers and around polystyrene panels. If you get it on something, it wipes off with mineral spirits. Contact areas should be dry and clean of contaminants, and good ventilation is recommended.

 

5. LIQUID NAILS AS-825 Acoustical Sound Sealant

Liquid Nails acoustical sealant is a durable elastic latex material. It meets ASTM E 90 standards for acoustic properties and is non-flammable as per ASTM E 84. Liquid Nails is a low odor, VOC compliant, and water-soluble. A 28-ounce cylinder will cover approximately 86 linear feet with 1/4″ bead. A quart caulking gun is required for the canister, though.

The sealant bonds to most building materials, but isn’t recommended for non-porous surfaces, around PVC pipes, plastics, or wet areas. Liquid Nails stays flexible, helping it to stop sound wave vibration and improving wall assembly STC ratings.

Apply the caulking to seams, gaps, wall perimeters, and around cut-outs and utility boxes to prevent air and sound movement. Surfaces should be free of dust and dry for full adhesion.

 

6. OSI SC175 Draft and Acoustical Sound Sealant

OSI Acoustic Sealant is a paintable, latex-based non-flammable material that seals gaps, cut-outs, and joints. Though VOC compliant, it should be used in a ventilated area. It is easy to use, is tack free in 30-minutes, and cures in 2 to 7 days.

The white sealant stays flexible and prevents sound and air movement. A 1/4″ bead will cover 86 linear feet, and a 3/8” about 38 feet. It cleans-up with water and soap.

The Sound Sealant sticks to most building materials and decreases sound transfer and drafts. It works well in commercial and residential locations for new builds and renovations.

Depending on wall construction and application, the sealant can improve STC values by 9 to 40 points. It is also effective for sealing base and top plates. Once cured, OSI Acoustic Sealant is not affected by freeze-thaw so it can be used in protected exterior locations.

OSI SC175 shouldn’t be used in wet or underwater applications. Nor is it recommended for use on metals that corrode or between non-porous surfaces. The sealant also doesn’t adhere well to cement board, polypropylene, polyethylene, or other nylon materials.

 

7. QuietRock EZ-SNAP

QuietRock EZ-Snap is an acoustic damping drywall panel. The 5/8” sheet has an anti-vibrational core the stops sound wave penetration. It is available in 4-foot widths, and 8, 9, or 10-foot lengths. There is no mess, no curing time, and it installs and cuts like regular gypsum board.

A 4’x8’ sheet weighs 83.2–pounds and can be used on walls and ceilings. EZ-Snap can be fastened to studs or joists, or directly to existing drywall. It also finishes the same as standard gypsum panels, so no special tools are required.

EZ-Snap outperforms standard drywall in similar construction practices and provides better STC values. STC results range from 49 to 60, depending on the wall assembly. When coupled with acoustic sealants, the values can be even higher.

One 5/8” sheet provides similar sound control to two 5/8” sheets with Green Glue sandwiched between, at a similar price point. However, Labor and time are the big savings in comparison, plus it provides faster attenuation results. It doesn’t take a month to cure, nor does it ooze at the edges.

 

Alternatives To Green Glue That Do Not Work

Other products have been recommended as alternatives to Green Glue. Unfortunately, some that have been recommended don’t work.

DYNAFLEX 230 is one that has been recommended as it fills cracks and gaps up to an inch wide, is crack-proof, flexible, and adheres to most building materials. Unfortunately, it cures harder than acoustic sealants and is less flexible. Additionally, the harder formulation actually enhances sound vibration transfer.

Sealant silicons are good water and draft stoppers as they don’t shrink or crack. They also maintain some pliability and flexibility. An acoustic sealant is more durable, flexible, and won’t shrink or crack over the years, so it’s a better solution. Regular silicone caulking won’t stay flexible like rubbery acoustic caulk, and it will dry out and crack, allowing sound through.

SMT Red Glue is a Poly dilute paste-like compound. It is used to glue components to PCB boards before soldering. The paste is temperature sensitive and hardens as it is heated. Other heat tolerant sealants or silicones also cure hard as they dry out, making them ideal agents for sound wave transfer.

Polyurethane is a plastic-like polymer that can be soft, hard, sticky, rubbery, flexible, or protective like varnish. Products that are soft polyurethane foam are not used in wall construction. They may be used strategically inside a room to absorb sound energy, but will not stop sound penetration in or out of a room.

Spray foams used to fill wall cavities harden and actually increase the sound transfer through the wall. Varnish like polyurethane will cure to a hard, durable finish on wood. None of the polyurethane formulations are alternatives to Green Glue.

Conclusion

There are alternatives to Green Glue that work. The products shared will perform with similar STC results to both the compound and the sealant. Look for materials that will isolate or damp sound waves, and remain elastic.

The concept is to catch the frequency waves and convert the energy to heat, thereby control sound movement. Hopefully, you found this article helpful. If you know someone who may also like it, please share it. Your comments and suggestions are always appreciated.

 

Photo of author

Author S Krone

A lawyer never retires. So I would just say that I am not as active as I used to be. Now I simply dedicate myself to fishing, my hobby, and my grandchildren. For Business Finance News I write about legal aspects of mortgage policies, mostly regarding the rights of policyholders. I also have articles about personal injuries.

Thank you for visiting businessfinancenews.com

Leave a Comment

Business Finance

About Us

Business Finance News is a brand oriented to business owners and dedicated to analyzing and comparing the cost and conditions of B2B procurement of goods and services through free quotes delivered by business partners.

Contact

Address 5050 Quorum Drive, (75254) Dallas TX

telephone 844-368-6072

DISCLAIMER

A personal loan is a medium term loan with a fixed interest rate that is repaid in equal monthly payments and it's usually limited to 24 months. Loan offers and eligibility depend on your individual credit profile. Our lenders can help you obtain as much as $3,000 depending on the lender, your state and your financial situation.

The owner and operator of businessfinancenews.com is not a lender and is not involved into making credit decisions associated with lending or making loan offers. Instead, the website is designed only for a matching service, which enables the users contact with the lenders and third parties. The website does not charge any fees for its service, nor does it oblige any user to initiate contact with any of the lenders or third parties or accept any loan product or service offered by the lenders. All the data concerning personal loan products and the industry is presented on the website for information purposes only.

Businessfinancenews.com does not endorse any particular lender, nor does it represent or is responsible for the actions or inactions of the lenders. Businessfinancenews.com does not collect, store or has access to the information regarding the fees and charges associated with the contacting lenders and/or any loan products. Online personal loans are not available in all the states. Not all the lenders in the network can provide the loans up to $3,000. Businessfinancenews.com cannot guarantee that the user of the website will be approved by any lender or for any loan product, will be matched with a lender, or if matched, will receive a personal loan offer on the terms requested in the online form. The lenders may need to perform credit check via one or more credit bureaus, including but not limited to major credit bureaus in order to determine credit reliability and the scopes of credit products to offer. The lenders in the network may need to perform additional verifications, including but not limited to social security number, driver license number, national ID or other identification documents. The terms and scopes of loan products vary from lender to lender and can depend on numerous factors, including but not limited to the state of residence and credit standing of the applicant, as well as the terms determined by each lender individually. 

APR REPRESENTATIVE

APR (Annual Percentage Rate) is the loan rate calculated for the annual term. Since businessfinancenews.com is not a lender and has no information regarding the terms and other details of personal loan products offered by lenders individually, businessfinancenews.com cannot provide the exact APR charged for any loan product offered by the lenders. The APRs greatly vary from lender to lender, state to state and depend on numerous factors, including but not limited to the credit standing of an applicant. Additional charges associated with the loan offer, including but not limited to origination fees, late payment, non-payment charges and penalties, as well as non-financial actions, such as late payment reporting and debt collection actions, may be applied by the lenders. These financial and non-financial actions have nothing to do with businessfinancenews.com, and businessfinancenews.com has no information regaining whatsoever actions may be taken by the lenders. All the financial and non-financial charges and actions are to be disclosed in any particular loan agreement in a clear and transparent manner. The APR is calculated as the annual charge and is not a financial charge for a personal loan product. 

Late Payment Implications

It is highly recommended to contact the lender if late payment is expected or considered possible. In this case, late payment fees and charges may be implied. Federal and state regulations are determined for the cases of late payment and may vary from case to case. All the details concerning the procedures and costs associated with late payment are disclosed in loan agreement and should be reviewed prior to signing any related document. 

Non-payment Implications

Financial and non-financial penalties may be implied in cases of non-payment or missed payment. Fees and other financial charges for late payment are to be disclosed in loan agreement. Additional actions related to non-payment, such as renewals, may be implied upon given consent. The terms of renewal are to be disclosed in each loan agreement individually. Additional charges and fees associated with renewal may be applied. 

Debt collection practices and other related procedures may be performed. All the actions related to these practices are adjusted to Fair Debt Collection Practices Act regulations and other applicable federal and state laws in order to protect consumers from unfair lending and negative borrowing experience. The majority of lenders do not refer to outside collection agencies and attempt to collect the debt via in-house means. 

Non-payment and late payment may have negative impact on the borrowers’ credit standing and downgrade their credit scores, as the lenders may report delinquency to credit bureaus, including but not limited to Equifax, Transunion, and Experian. In this case the results of non-payment and late payment may be recorded and remain in credit reports for the determined amount of time.